How To Set Timer On Pool

Download Commodity

Download Commodity

If yous own a pool, a pool timer is an invaluable tool that lets yous activate its pumps during specific times of the day. This can help you save coin on power and proceed your puddle's chemical's good for you and balanced. If y'all're unsure of how to set and use a puddle timer, don't worry—it's very simple!

1. 1

   Locate the clock punch inside the timer box. Open your puddle timer box and look for the clock punch—on most models, information technology's yellow in color with a small blood-red or silvery handle outstretching from it. On the clock-dial is a silver time pointer that points to the current fourth dimension.^[1]

   • Read your manufacturer's instructions to determine the parts of the dial.

2. 2

   Pull the clock dial outward and plow information technology to the time of day. Grip the clock dial and gently pull it outward. Afterward, rotate the punch either clockwise or counterclockwise until the silverish time pointer aligns with the time of day.^[2]

   • Take note of the AM and PM times along the punch. For case, if information technology'due south 12 PM, rotate the clock dial until the argent fourth dimension pointer aligns with 12 PM.

   Advertisement

3. three

   Locate the "On" tripper for your pool timer. The trippers are clipped to the timer and determine when your puddle equipment turns on and off. On most models, the "On" tipper is green and contains an "On" label.^[3]

   • In some puddle timer models, the "On" tripper is silver.

4. four

   Attach the "On" tripper to the desired time on the clock punch. Later finding the "On" tripper, locate the fourth dimension on the clock dial that y'all desire your equipment to turn on. Now, hold the tripper to this time on the clock dial and tighten the screw on the tripper until it's firmly attached.^[4]

   • If you desire to set your pool equipment to turn on at 8 AM, attach the tripper to this spot on the clock dial.
   • Remember that the silver time indicate represents the current time and is separate from the tripper fourth dimension.

5. five

   Find the "Off" tripper for your puddle timer. The "Off" tripper will decide when your puddle equipment turns off. Typically, this tripper is golden and labeled with "Off."^[5]

   • Some puddle timer models accept silver "Off" trippers.

6. 6

   Connect the "Off" tripper to the desired fourth dimension on the clock dial. Once you find the "Off" tripper, locate the time on the clock dial that you want your puddle equipment to turn off. Afterward, concur the tripper to this time and tighten its screw until information technology'southward firmly connected.^{[half dozen]}

   • If you desire your pool equipment to plow off at three PM, connect the tripper to this time on the clock dial. If your "On" tripper is currently at 8 AM, that ways your equipment will plow on at this time and off at 3 PM.

7. vii

   Flip the ruby-red or silver lever to override the current timer setting. The ruddy lever extending from your clock dial can be used to do the opposite of your electric current setting. For example, if your timer is currently off and yous desire to turn it on, flip the lever to "On." Now, the timer will remain in this mode on until the silver fourth dimension point reaches your "Off" tripper or yous flip the red lever to "Off."^[seven]

   • Spray WD-40 backside the punch if your ruby override lever is hard to flip. If this doesn't work, you might have an insect infestation behind the time clock.

Advertisement

1. 1

   Check the chemical residual of your pool. Before using your timer to optimize your pump, you need to determine that your puddle'south pH, alkalinity, and calcium hardness are seven.4 to vii.6, 100 to 150 ppm, and 150 to 400 ppm, respectively. Use h2o testing papers to check these values and arrange them every bit necessary.^[8]

   • To enhance your puddle's pH, add sodium carbonate or sodium bicarbonate. To lower it, add muriatic acid or sodium bisulfate.
   • Add sodium bicarbonate to enhance alkalinity and pH reducer or muriatic acid to lower information technology.
   • Add together calcium chloride to raise calcium hardness and muriatic acid to lower it.

2. 2

   Run your pool filter at to the lowest degree 12 hours a day between 9 PM and 9 AM. In most cases, 12 hours a twenty-four hour period is the minimum to go along your pool filter running. Depending on where yous live, different times of day are almost beneficial—contact your energy company and ask for optimal times.^[9]

   • In most cases, 9 PM to nine AM and the optimal times to run your pool filter since this is when people are using less free energy.

3. 3

   Check your pool'south chemical balance the twenty-four hours after the first test. After letting your pump run for 12 hours, check its chemical balance again. If your pump is running for the proper amount of time, the levels should be the same. If they are less or more than the offset exam, record these differences.

   • Examination your pool's chemical balance one to 3 times a week.

4. iv

   Reduce or increase your puddle'southward filter time past 2 hours every bit necessary. In many cases, pool pump horsepower is more than necessary for pool size. If y'all discover that your pump is pushing your pool water through in less time and causing lower chemical levels than required, remove 2 hours from your timer and run a chemical exam again the next day. If it's causing higher chemical levels than required, add 2 hours and run a chemical exam the adjacent day.^[10]

   • Proceed checking your pool chemical balance and reduce or add time until you find the optimal runtime. Recall that optimal pump time can salve you money on your free energy bill.

Advertising

Enquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• Reset your timer clock at any fourth dimension by pulling the xanthous dial outward toward y'all to disengage it. Now, spin it in either direction to set the fourth dimension with the eye fourth dimension pointer.

• If your time pointer is loose, tighten the screw holding it in place. If this still doesn't work, you might need to replace the small spring located behind the spiral if it'southward broken or rusted.

Thanks for submitting a tip for review!

Advertisement

• Never touch behind the plastic insulation under the timer or yous chance electrocution.

Advertisement

About This Article

Commodity Summary 10

To set the timer on your pool, starting time by locating it in the timer box. It will virtually probable look like a yellow circle with a pointer indicating the time. Pull out the punch and twist it to fix it to the right time of twenty-four hours. Then, attach your "On" tripper, which will actuate your filter, to the fourth dimension on the clock when you lot want your equipment to turn on. Side by side, connect your "Off" tripper to the time y'all want to turn it off. If you want to override the setting you've made, flip the ruby lever on your dial, which will turn the equipment on if it'south currently off. For tips on how oftentimes to run your pool filter each day, keep reading!

Did this summary aid you?

Thanks to all authors for creating a page that has been read 55,324 times.

Did this commodity help you?

Source: https://www.wikihow.com/Set-a-Pool-Timer

Share this post